E-Z Stone Prime Coat is a premium waterbased primer and bonding adhesive specifically formulated for the application of the E-Z Stone Decorative Coating. E-Z Stone Prime Coat provides maximum adhesion and coverage of the E-Z Stone Decorative Coating for interior, exterior applications. E-Z Stone Prime Coat can be applied on vertical and horizontal surfaces such as concrete, masonry, drywall and wood, paving the way for the application of the E-Z Stone Decorative Stone Coating.

YOU NEED: kneepads, paint roller & brush, gloves, protective clothing and eye glasses.

APPLICATION: Thoroughly mix the product. Uniformly apply a thin undiluted coat using a roller or soft bristle brush. Do not allow to puddle. Protect the primed area until application of E-Z Stone Decorative Coating. Allow to dry 4 hours or until tack free (dry time may be extended in damp or cool conditions).

LIMITATIONS: Apply when the ambient air and surface temperature is between 10ºC (50ºF) and 40ºC (104ºF). Do not apply if surface and air temperature are or will fall below 10ºC (50ºF) for at least 24 hours. Do not apply if rain is forecast within a minimum of 24 hours

COVERAGE: The coverage rate may vary depending on the surface to which the product is applied and the skill of the applicator. One coat will cover approx. 14.9 m² (160 sq ft.) per 3.78L (1 gallon).

YOU NEED: steel pool trowel, kneepads, gloves, protective clothing & eye glasses.

APPLICATION: Thoroughly stir E-Z Stone Coating prior to application with a paint stick or power drill and a mixing paddle. Apply coating to a smooth surface in small workable areas. Press firmly applying E-Z Stone Coating to approx. 1.6 mm (1/16") thickness using a steel trowel at about a 10°–15° angle (recommended round pool trowel). If lighter coloration or pinholes appear on dried finished areas, re-apply a thin coat of E-Z Stone Coating to achieve required thickness & colour. FOR MAXIMUM CONTROL AND BEST APPEARANCE, TWO THIN COATS ARE RECOMMENDED. Allow 4–6 hours between coats. During trowel application smooth out any ridges or trowel marks with a smoothing sweep of the trowel. E-Z Stone decorative coating can also be spray applied with a hopper gun & air compressor, holding pistol approx. 46 cm (18") away from surface, then smooth& press with a trowel. The finished surface must be protected from rain, condensation, dew or freezing for at least 24 hours after application.

LIMITATIONS: Apply between 10ºC (50ºF) and 40ºC (104ºF). Do not apply if surface and air temperature are or will fall below 10ºC (50ºF) for at least 24 hours. Do not apply if rain is forecast within a minimum of 24 hours

COVERAGE: 3.78 L (1 U.S. Gallon) will cover approximately 33.3 m2 (35 sq. ft.) with one coat - we recommend applying two thin coats on horizontal applications.

E-Z Stone Protective Sealer is a premium, high performance acrylic, exterior/interior,
waterbased clear sealer specially formulated to protect and maintain the fresh
appearance of the E-Z Stone Decorative Coating. E-Z Stone Protective Sealer protects
against damaging water, liquid, gas, oil and chemical spills, as well as harmful salts and
outside weathering.

YOU NEED: paint roller or brush, paint tray, gloves, protective clothing & eye glasses.

APPLICATION: Ensure surface is clear from dirt and debris. Pour sealer into a paint tray and apply a thin coat either with a roller or airless spray equipment. The roller should have a 6 mm (1/4") nap.
Use light pressure to achieve a thin, even application. A second coat is recommended for maximum protection and durability. The first coat must be dry to the touch (a minimum of 4 hours) before the
second coat is applied. After applying the second coat, the surface must be allowed to fully cure before exposing to traffic of any kind. Drying and curing times will vary according to temperature and humidity conditions. Apply in dry conditions, in the morning or late afternoon, to avoid excessive mid-day heat. Allow 8 hours for light traffic & 24 hours for heavy traffic. Apply between 10°C (50°F) and 40°C (104°F). Do not apply if surface and air temperature are or will fall below 10°C (50°F) for at least 24 hours. Do not apply if rain is forecast within a minimum of 24 hours.

COVERAGE: 3.78 L (1 U.S. Gallon) will cover approximately 37.2 m2 (400 sq. ft.) with one coat over a smooth surface. On a rough surface the coverage will be less.